Home Communities Technology How mmWaves impact cables, connectors, and PCB traces
TechnologyTech & gadgets

How mmWaves impact cables, connectors, and PCB traces

Share
How mmWaves affect cables, connectors, and PCB traces
Share

Millimeter-wave signals are used in 5G networks to provide high data rates and wide bandwidth, opening the door to countless applications such as object detection, ranging, and mapping. However, these signals can be difficult to design for due to signal losses that can occur both through interconnects and over the air. 

One way to overcome these challenges is to implement solid design practices that minimize losses. The mmWave signals have wavelengths that typically range from 1 mm to 10 mm, covering frequencies between 30 GHz to 300 GHz. In 5G, mmWave starts at 24 GHz and is often referred to as Extremely High Frequency (EHF). Frequencies below EHF are classified as Super High Frequency (SHF), while those above it are considered Tremendously High Frequency (THF).

Also read: Revolutionizing 5G Testing: Rohde & Schwarz Unveils Compact Conformance Test Systems At MWC 2024

RF

Figure 1. RF spectrum highlighting the mmWave region.

At mmWave frequencies, signals lose strength from absorption in the atmosphere, which limits their travel distance. This absorption results from the presence of oxygen in the atmosphere, both in elemental form and in water vapor. While such signal degradation is often a drawback in many radio systems, it is surprisingly useful for high-bandwidth networks.

By preventing signals from traveling too far, you can reuse the same frequencies in other nearby networks without interference. The higher frequency of mmWave compared to Wi-Fi also allows for far more bandwidth, which is one of the many reasons why 5G networks utilize mmWave.

The wide bandwidth of mmWave leaves plenty of room for expansion, meaning that mmWave is unlikely to become congested for the foreseeable future. The high frequency also means that equipment can use small antennas, making them easy to integrate into small devices. This small size also makes the construction of small-scale phased array antennas feasible.

Phased arrays make beamforming possible, which lets multiple devices share the same frequency without interfering with each other. mmWave systems (especially 5G) can handle thousands of devices simultaneously while ensuring that each device can take full advantage of the bandwidths offered by the higher frequencies.

Unlike signals at lower frequencies, mmWave is extremely directional, operating more like a laser beam than a wave that diverges drastically from its source. This means that mmWave applications operate more on a line-of-sight basis, thereby reducing interference between different mmWave devices.

What challenges does mmWave introduce?

You might think that mmWave’s high bandwidth capabilities, lack of interference, and directional nature make it the ideal frequency range for any communication network. That’s not necessarily the case.

Also read: Revolutionizing Wireless Communication: Metasurfaces Paving The Way For Next-Generation Connectivity

High attenuation from the atmosphere often limits transmission distances to just 100 m, though experiments have reached distances of 10 km under the right conditions. In the case of 5G networks, the high attenuation, and resulting short range requires numerous 5G cells near users, which significantly increases the cost of building and maintaining a reliable network.

Of course, this would apply to any mmWave network, including those used in consumer, commercial, and industrial environments. This is why other network technologies utilizing lower frequencies such as 2.4 GHz and 5 GHz Wi-Fi are often preferred.

The high frequencies associated with mmWave can push traditional semiconductors to their limits. For example, circuits utilizing traditional silicon can’t go beyond 190 GHz, making the entire frequency range above 190 GHz inaccessible. That’s why other processes, such as GaN, come into use.

PCB traces

When operating at mmWave frequencies, PCB traces become more complicated because of signal degradation. Furthermore, PCBs also introduce numerous challenges in their design, including interference from other circuits, the choice of dielectric, subtle variations in identical PCBs, and even environmental conditions of the day. (For example, the direction of cleaning copper clad layers during manufacture can change the signal integrity performance of a trace).

Furthermore, trying to get mmWave frequencies to travel through a PCB can also challenge you because signals can radiate from the tail ends of vias that are not fully connected. The change in material from trace to via can also induce losses and reflections, which are only more problematic in connectors. This is especially true for connectors that utilize mating contacts where the contact point between two connectors isn’t at the ends of the contacts.

If long cable lengths carry mmWave signals, then the exact length of that cable assembly will determine the signal degradation; mismatched lengths and impendences will result in reflections. At low frequencies, slight mismatches are not massively degrading, but when dealing with mmWave, even the smallest mismatch can destroy signal fidelity.

What can you do?

You can follow numerous steps to solve the numerous challenges that mmWave frequencies bring. Unfortunately, you can’t skip any of these steps.

Also reaD: 6G Could Enhance Cellular Networks With Sensing Capabilities

First, any connector, cable, or PCB trace intended to carry mmWave signals needs construction that uses high-grade materials to minimize signal loss. Furthermore, they should also be rated for the expected frequency ranges.

To minimize signal losses, connectors should make full contact along the entire conductor. All conductors need termination. Connectors often use a cage whereby a socket connector can grab and fully enclose a plug connector from the tip to the base. Figure 2 shows examples of such connectors.

SMA cable

Figure 2. SMA and SMP RF cable assemblies minimize signal losses at mmWave frequencies.

For designs that require PCB traces, you must ensure that traces avoid turns and vias. If you must use vias, then you must terminate the end of the via with a trace. Unconnected vias not only act as reflection points; they can also radiate signals, which introduces EMI issues.

Any mmWave communication between two boards takes place through coax cables or flyover cables, but the length of the cable should carefully match the wavelength of the intended signal.

Cables and connectors

Engineers have numerous options from many companies for connecting mmWave systems, such as quick-connect connectors. These assemblies utilize high-quality dielectrics and conductor materials and are manufactured to specific sizes and lengths to reduce signal reflections. These are commonly used in high-volume manufacturing due to the reduced mating/de-matting time and the availability of ganged connectors.

Such assemblies are often already terminated, which simplifies the installation of mmWave cabling. For applications that have specific requirements, many manufacturers also offer custom cable assemblies that provide phase matching or can operate in extreme environments.

Angled RF connector

Figure 3. Angled RF connectors reduce cable strain and improve VSWR.

The choice of connector mounting is also essential in any mmWave design. Angled connectors (30° and 45° with respect to PCB) are ideal for use for a wide range of frequencies (up to 26.5 GHz). Angled connectors (Figure 3), available from numerous manufacturers, provide strain relief to cables (essential in mmWave applications) and improve voltage standing wave ratio (VSWR) ratings (up to 1.30) compared to vertical (90°) mount connectors.

Some mmWave systems can experience shock and vibration. For these applications, SMP3 coax connectors can help engineers thanks to their 30% smaller design compared to SMPM and a floating bullet. With a maximum frequency of 67 GHz and a VSWR of 1.50, these connectors offer engineers options for mmWave applications in harsh environments.

Also read: AccelerComm Launches PUSCH Channel End-To-End Simulator For 5G Network Optimization

Conclusion

mmWave’s high frequency, large bandwidth, line-of-sight behavior, and easy manipulation through miniature phased arrays can provide wireless devices with high data rates. For all the benefits that it provides, it also faces numerous challenges if not properly addressed. Thus, you must understand the design constraints that mmWave presents, use best RF practices when designing PCBs, and carefully choose connectors made from high-quality brass, beryllium copper, or stainless steel to ensure ruggedness and high performance.

Share

Leave a comment

Leave a Reply

Your email address will not be published. Required fields are marked *

Latest Posts

Related Articles
Standards group to address 6G multiple access
TechnologyTech & gadgets

ETSI Launches Industry Group to Tackle 6G Multiple Access Techniques

ETSI has established a new Industry Specification Group (ISG) focused on Multiple...

What is a scheduler and what does it do in a 5G network?
TechnologyTech & gadgets

Understanding the Role of a Scheduler in 5G Networks

A scheduler dynamically allocates resources, including time, frequency, and power, to serve...

Wi-Fi HaLow SoC transfers data at 43.3 Mbps
TechnologyTech & gadgets

Morse Micro Unveils Next-Generation Wi-Fi HaLow SoC with Enhanced Performance

Morse Micro has announced the launch of its second-generation MM8108 System-on-Chip (SoC)....

How are the thermal issues with 5G radios being addressed?
TechnologyTech & gadgets

How are the thermal challenges of 5G radios being resolved?

All options are deployed when dealing with 5G radio thermal issues in...